A Husqvarna Lawn Mower Won’t Start For These 17 Reasons

I get extremely frustrated when my lawn mower breaks down. However, since I cannot afford to be without it for a long period of time, I try my best to figure out what the problem is.

Occasionally, while using a Husqvarna lawn mower, the engine will not start because it is not receiving the air, fuel, or spark that it needs to work. Typically, this occurs after a clogged air filter, dirty carburetor, damaged safety switch, faulty gas cap, plugged fuel filter, clogged fuel line, faulty starter solenoid, or a faulty fuel pump is installed in the vehicle.

In a Husqvarna Lawn Mower Won’t Start, there are a number of components that may fail and result in your mower not starting. You may find that the carburetor float bowl contains old or damaged fuel. The ingredients in fuel may evaporate over time, making the substance thicker and stickier after it has evaporated, leaving behind a thicker, stickier residue. During the start-up process, the carburetor may become clogged up with this sticky fuel, preventing the engine from starting. Try cleaning the carburetor with a carburetor cleaner if there is clogging in the carburetor. 

Here I have put together a list of everything you need to check if you are having difficulty starting your computer.

Why Your Husqvarna Mower Won’t Start

Husqvarna Gas Tank is Null

Why is gasoline drained? Your garden tools shouldn’t be used with old gasoline because it can damage them. Two months later, particles sink and the gasoline becomes less clean. It’s not a smart idea to store old gasoline in the shed with lawn mowers, hedge trimmers, leaf blowers, and chainsaws.

Where can I find the cause of my gas tank not filling up? Your vehicle’s vent/purge system may be malfunctioning if it happens at every gas station. The vapor inside the tank expands when you fill it. Using charcoal and a purge valve, they do so.

Solution:

In order to make sure that your Husqvarna lawn mower performs as well as possible, proper gas quality is crucial. As far as fuels are concerned, you should always use fresh unleaded gasoline with a minimum 87 octane rating when it comes to running your car. When using ethanol-free fuel, you should take care as it may damage your Husqvarna lawn mower if not installed properly, since it could cause the engine to overheat.

What kind of gas should I use in my Husqvarna riding mower?

We recommend using 89-octane E10 gasoline in all Husqvarna equipment that is currently available today, which is a mid-grade fuel that is between regular and premium fuel, and is suitable for use in all Husqvarna equipment.

Fuel tanks should be drained and flushed in order to prevent contamination. Sea Foam fuel additive is a simple way to clean your fuel system by adding fresh fuel with a fuel additive to your fuel.

I can’t vent the gas cap on my Husqvarna

Identifying the canister vent line of the gas tank is very critical if you are experiencing gas tank problems. Using a stick or a rod that fits into the vent, poke to see if there is any blockage. It is also possible to use compressed air. When you are finished draining the tank, empty out the air from inside, and then refill it with water.

Gas cap vents: how do they work?

It is noted that the quantity of gas in the tank reduces as the mower uses gas. In addition, a large part of the gas is replaced by air as the gas is burned. The gas cap has a vent through which air can be introduced. This air takes up space that used to be occupied by gasoline in the gas tank.

Are vented gas caps able to vent both ways?

There is a vented cap on the left that dates back to 1956. I would like you to note that the hole in the middle is quite large. This is a picture of the underside of a vented cap that was made in 1956. In these caps, both directions of airflow are allowed to flow through them.

Solution:

If you are starting at the center of the edge of the cap, stop when it reaches the middle of the edge. After that, drill another hole perpendicular to the first hole through the edge of the cap to meet up with that small diameter hole, i.e., approximately 1/16″. It allows you to vent your vessel, and the 90-degree turn reduces the chance that oil or gas will find its way outside of your vessel. 

Cleaning and clearing vents

• Your roof is yours
• Hold your hand over the vent while an assistant flushes the toilet
• A plumber’s snake can be used to unclog the stoppage.
• Using a garden hose, flush out the remaining debris if your “snake” can’t completely remove the clog.

Mower with a loose connection or weak spark plug

Wear and dirty spark plugs require more effort to produce a spark. This results in more tugging. It is possible that a damaged spark plug is the cause of your mower not starting recently, not starting properly, and/or needing to be rewinded repeatedly.

The engine cylinder may misfire or sound struggling due to a damaged spark plug. While you are mowing, your engine might even shut down completely, which would be something to worry about. In addition, you may notice that when the mower dies for the second time, you will have increasingly difficult difficulties restarting it each time it dies. 

Incorrect heat range, improper gapping, or chemical contamination can cause a spark plug to fail. The reason for 90 percent of spark plug damage claims is that too much voltage is applied to the spark plug. Incorrect temperature range, improper gapping, or chemical contamination can all be contributory factors to a spark plug failing.

Solution:

Affecting Spark Plugs: How To Clean?

If you want to clean a spark plug safely, you should use a wire brush or a spray-on plug cleaner that is specifically designed to be sprayed on ignition parts such as spark plugs. These deposits can also be scraped off with a sturdy knife. We would like to remind you that shot blasters and abrasives should NEVER be used to remove spark plugs.  

What is the proper way to tighten a spark plug?

• The loose spark plug(s) are located under the hood of your car. Open the hood and locate them.
• Remove any loose debris or grime from the threads of the spark plug and cylinder head using a microfiber towel.
• When the gasket touches the cylinder head, twist the spark plug.
• You can now tighten the plug with a torque wrench. 

In a Husqvarna lawn mower, the air filter

Maintaining a healthy and safe environment requires changing the air filter on your lawnmower. Overheating, inefficiency, pollution, and even fire hazards can occur due to clogged or dirty air filters.

Sputtering engines, loss of power, reluctance to start, and black smoke coming from the exhaust are some of the most common symptoms of dirty lawn mower air filters.

Solution:

Make sure the filter can be cleaned and reused or if it needs to be replaced. You will need to remove the paper air filter from the air filter housing while taking care to avoid knocking dirt into the air intake as you do so. Any dirt that remains in the housing should be wiped out with a fresh, dry cloth after cleaning it.

Air filter cleaning instructions:

• It is recommended that you remove the filter. It is recommended that you remove the air filter from the car and take care to ensure there is no dirt or dust falling into the airbox or intake.
• The cleaning solution should be applied to the surface. Let the filter soak in Simple Green All-Purpose Cleaner for some time, after which you can spray it with the cleaner.
• Rinse well.
• A dry environment.
• The oil should be changed and the filter should be oiled.

There is a problem with the fuel pump on the Husqvarna

A failing/failed fuel pump will cause major performance and drivability issues with your vehicle. If your fuel-to-air ratio is off and the cylinders aren’t getting enough fuel, then the pistons aren’t firing and your engine is struggling to move the vehicle forward.

Solution:

It is possible to restart your car even if the fuel pump has become damaged in your vehicle. So long as it has not completely stopped working – by applying manual pressure, connecting a fuel pressure gauge, or making sure the engine receives steady heat – you should still be able to start the vehicle. 

You can test the flow of fuel by using the fuel shut-off valve or the fuel clamps to start and stop fuel flow at different times. The fuel shut-off valve may not be available on all mowers. Please note this.

Husqvarna Has a Blockage in the Fuel Line

In the long run, if you use the highest quality fuel in the world, you will notice that your fuel line will become clogged with gunk. You may find gunk in your fuel system if your engine is covered in debris or if your fuel contains imperfections. There are a variety of problems caused by clogged fuel lines, including engine sputtering, or a complete loss of engine power.

Solution:

A fuel system cleaner is an effective way of clearing sediment build up or any blockages in the fuel system of a vehicle that has an electric fuel pump. You can also open the pump to clear debris out of its internal filter if your vehicle has a manual one (usually found in older model vehicles). In most modern vehicles, though, that is not an option for those with an automatic transmission.  

Dirty Carburetor on Your Husqvarna

Whenever the carburetor is dirty, the air and fuel required to start the engine cannot travel through the passage because there is too much dirt. This results in a turnover but no catch or actual start, which results in a stall. You can tell it’s working efficiently because it’s smooth and lean. Whenever the balance between fuel and air is thrown off in an engine, this is referred to as “running lean”.

Solution:

A gallon of carburetor and parts cleaner is the easiest way to disinfect the carburetor and its parts. However, the price of the can is quite high for a single use of it. It is critical to follow the cleaning instructions on the can in order to ensure a thorough clean. Alternatively, you may be able to degrease parts by spraying carburetor and choke cleaner on them.

How to Clean a Carburetor on a Husqvarna Lawnmower, step by step

• Step 1: Make sure that the carburetor needs to be cleaned if it is dirty.
• Step 2: It is necessary to remove the air filter and fuel tank in order to be able to inspect the carburetor.

• Step 3: Unscrew the carburetor jets with a compressed air gun or carb cleaner and clean them with a compressed air gun.

Bad Battery, Loose Cables, or Corroded Terminals on Your Husqvarna Mower

There’s no denying that corroded batteries can cause an inefficient flow of energy through their terminals. This results in battery power decreasing due to a decrease in performance. As a rule of thumb, battery corrosion happens because electrolytes or electrolyte vapors are released from the top of the battery, which is the most common source of corrosion.

A lead-acid battery can suffer from corrosion when the volatile chemicals or gases inside the battery escape and come into contact with the highly-conductive metal of the battery terminal. When this happens, corrosion can occur.

Solution:

In order to prevent corrosion of the battery terminals, you should apply grease to the terminals. Usually, it comes in the form of a packet that looks like ketchup and can be found in any auto parts store. In addition to AMSOIL Heavy-Duty Metal Protector, it is another viable option that you should consider. On the terminals, the coating helps protect them from corrosion by providing a protective layer.

Bad Husqvarna Safety Switch   

When it comes to riding mowers, how do you find safety interlock switches? It is pertinent to note that our lawn and garden tractors are equipped with four safety interlock switches. Step-Thru® tractors have location points that differ slightly from box frame tractors that have location points. The Husqvarna lawn mower may not start again if this is the cause of the problem!

Start the vehicle by shifting into Park and then begin driving it. You should try starting the vehicle in neutral if you notice the engine does not crank when you step on the brake. There is a possibility that the neutral safety switch has been damaged if the engine turns on.

Solution:

The process of bypassing the safety switch involves disconnecting the spark plug wire or the battery terminals before you bypass the safety switch. There is no need to worry about getting electrocuted during the procedure. This is because the battery cables are unplugged, which cuts off the power to the engine, preventing the possibility of being electrocuted.

Husqvarna Ignition Switch Problem

If you turn the key on the ignition switch and place the key inside, you will not be able to start your Husqvarna or even turn it over. It may be that the ignition switch is the source of the problem.

­

Solution:

Using a multimeter, you can check the ignition switch to ensure that it is working properly. A faulty switch should be replaced as soon as possible. 

Bad Starter Solenoid on Your Husqvarna Mower

Activate the ignition by turning the key to the “On” position. The thick red wires that connect to the solenoid should be located on the large terminal posts on the solenoid, near the thick red wiring. A screwdriver’s shaft should be touched simultaneously to both of the large terminals with the metal shaft of the screwdriver. There is a possibility that the solenoid has failed if the engine starts and turns over.

Solution:

Once you have identified the cause of the problem, you may be able to easily replace or repair a failed solenoid. This will not interfere with the use of your machinery or the manufacturing process. However, it can be a debilitating problem for your manufacturing process.

In the case of a failed Husqvarna ignition coil, 

A malfunctioning ignition coil can cause your engine to misfire if it is not working properly. During normal driving speeds, it is common to experience a jerking or sputtering sensation as a result of a misfiring engine. Your vehicle may shake, vibrate or run rough when you stop due to a damaged ignition coil.

Solution:

With tools from your local AutoZone, you can replace an ignition coil at home. Many modern vehicles can be difficult to test/change an ignition coil, especially those with sideways engines.

Charging issue with a Husqvarna mower

The battery might need to be charged with a battery charger if it is not charging properly. There is a possibility, however, that despite the battery holding a charge, there may be some fault with it and the battery will have to be replaced. When the lawn mower is running, the alternator provides power to the engine and even recharges the battery while the engine is running. 

This problem can be caused by a variety of factors, such as loose, dirty, or corroded battery cables, electronic drain, or a degraded battery. These factors can all result in a drained lawn mower battery. Your lawn mower battery may also be draining due to a faulty charging system, a failed voltage regulator, or other issues that may be causing the battery to discharge.

Solution:

• There are a few things you can do to make sure your charging system is working correctly
• Replace the battery as soon as possible. A battery that is old and has problems charging should be changed if it has been in use for more than seven years.
• Make sure the battery is maintained.
• The parts of the charging system should be cleaned.
• The wiring needs to be checked.
• There is no need to add accessories.
• Check out the drive belt to see how it looks.
• There will be times when you will need to drive.
• Alternators need to be replaced as soon as possible.

Final Thoughts: 

The more you understand how your mower works, the more you will be able to troubleshoot it as soon as something is wrong. This will save you a lot of time and hassle. This guide is a helpful resource for novice mower owners who are having trouble starting Husqvarna Lawn Mower Won’t Start riding mowers or having trouble resolving any troubleshooting issues they may encounter. These tips are provided by our expert landscapers.

It is hoped that your Husqvarna lawn mower will be habituated to starting when it is turned on.