Troy-Bilt Lawn Mower is Cutting Uneven
Many different reasons can account for uneven cutting on your Troy-Bilt mower. It is good news, most of the time, that you can cut back on your severe cuts by repairing and adjusting them as needed.
If your lawn mower is cutting unevenly, leaving some parts long, while others are very short, you cannot just stand back and do nothing. This has been a terrible look! However, what is the right place to start?
How could this problem be caused? Should you buy a redesigned and improved mower? We’ll work together to find out what happened. Don’t worry, I’ll help you. A few quick checks can usually uncover the cause, based on my experience. There is generally an easy solution to the problem most of the timeTroy-Bilt Lawn Mower is Cutting Uneven.
Troy-Bilt Lawn Mower is Cutting Uneven
| Cause for Uneven Troy-Bilt Cut | Solution for Uneven Troy-Bilt Cut |
| Worn mower blade | Sharpen blade. Replace with a new blade when needed. |
| Low tire pressure | Check tire pressures and bring them to the correct level |
| Bent mower blade | Replace mower blade |
| The blade is incorrectly installed | Remove and install with the blade sail point upward |
| Clogged mower deck | Scrape the deck |
| The deck is not level | Level the deck from side to side & front-to-back |
| Damage to the spindle or spindle housing | Replace damaged spindle or housing |
| Bad deck belts or pulleys | Replace worn belts and pulleys |
| Engine speed is too low | Run your mower at full throttle |
| Ground speed is too fast | Mow at the correct speeds for your mowing conditions |
| Incorrect mowing paths | Overlap paths so strips of uncut grass are not left |
| The deck shell is damaged | Repair or replace your mower deck shell |
In what way can the desk alignment be adjusted?
Leveling the deck height is vital to cutting grass more precisely. Having an uneven deck causes the blades to scalp the lawn when mowing too close. Make sure the desk is parked on a flat surface before balancing it. Once the mower has been stabilized and the blades and moving parts have stopped, the mower should be stopped. Following that, measure the blade height from the edge to the ground and check the tires’ pressure. If there is a significant difference between the peaks, a link lock may have to be lifted. Raising and lowering the mower are done in opposite directions by turning the handle clockwise. The blade height difference should be no more than 1/8 inch. The heights can be measured using measuring tapes. Generally speaking, it’s acceptable for the front blade tips to be 1/8″ to 12″ lower than the rear blade tips.
Troy-Bil deck belt or pulley failure
Your Troy-Bilt mower belt can fail to move around the pulleys at high speeds, resulting in poor cutting results. To make sure you don’t have damaged pulleys or worn deck belts, inspect them.
You should rotate your pulleys slowly to check them for wear. Poorly designed pulleys can be felt as resistance or heard as noise when they are turned. Pulleys that appear to be defective should be replaced.
Whenever your belt looks shiny or worn, it is a sign that it is damaged. Due to wear or friction with other deck components, it may also fray, stretch, or crack over time.
It is advisable to replace a worn mower deck belt with a new one that is compatible. Using belts from the manufacturer ensures that I’m getting a high-quality, properly-sized belt.
An issue with the deck shell of a Troy-Bilt mower
When your mower deck is damaged, your mower will give you an uneven or sloppy cut. If you got moving a bit too fast, you might have hit an obstruction. The deck shell may be repaired or replaced.
If your Troy-Bilt dealer replaces your deck shell, you may want them to quote the entire deck assembly as well.
When your mower deck is beyond repair, you will need to swap all the components over to an updated deck shell. It might be better to just replace it with a refurbished one.
Have Troy-Bilt lawn mower problems?
A lawn mower with enough time will begin to display problems including failing to start, not running, smoking, leaking gas, giving a rough cut, vibrating, etc.
You can use this guide to troubleshoot the next problem that comes up on your Troy-Bilt mower and save time and money.
Typical Troy-Bilt Lawn Mower Problems & Solutions.
You should always hire a professional to diagnose and repair your lawn mower if you are not confident about repair work.
We will make sure that you and the mower are safe. Find a Troy-Bilt dealer or a lawn mower repair shop
Your Troy-Bilt is overlapping the path
Your lawn mower will mow more quickly if you make fewer passes, but you may leave bits of uncut grass if you don’t overlap your cuts properly.
To ensure your mowing job lasts longer, experiment with your mowing paths if you’re a first-time customer to make sure you are correctly overlapping the cuts without overlapping too much.
Conclusions:
As a result, everyone needs their lawnmower to work correctly and cut grass evenly so their backyards look neat. When a lawnmower does not clip the grass evenly, it can be frustrating. In this article, we discussed briefly why mowers cut unevenly. You might face the same problem if your mower is not cutting the grass more accurately. Go through the reasons and follow the solutions mentioned above. Make sure your lawn looks the way you want it by following these tips and guidelines. Always take good care of safety precautions before servicing or repairing power equipment. I hope these guidelines and tips will assist you with your common mowing issues Troy-Bilt Lawn Mower is Cutting Uneven.
